BSOD ကုတ္ေလးေတြေပါ့

Error
Error message


Troubleshooting recommendation

Stop 0×0000000A = Replace/remove hardware, roll back, or update driver.

Stop 0×0000001E = Recently installed or defective software crashed the OS. Report the error and update or remove the software.

Stop 0×00000024 = Probable disk or file system error. Run CHKDSK to determine disk problems.

Stop 0×0000002E = Defective or mismatched memory, including motherboard, Level 2 cache, or video RAM. Replace memory or system board. May also be caused by pagefile or disk error. Run CHKDSK to determine disk/file system problems.

Stop 0×0000003F = Removing or reinstalling upgraded software may solve this problem.

Stop 0×00000050 = Replacing RAM memory, L2 RAM cache, video RAM, or incompatible software, including remote control and antivirus software, are possible fixes.

Stop 0×00000077 = Run a virus protection scan to locate and remove any possible virus infections. Run CHKDSK or other disk-repair diagnostic or replacing the hard drive may resolve this problem.

Stop 0×00000079 = This error most often occurs when ACPI firmware settings are changed. For example, you might install Windows XP Professional on an x86-based computer with the firmware ACPI enable option enabled and later decide to disable it.

This error can also result when mismatched single and multiprocessor configuration files are copied to the system.

Re-enable ACPI or run Windows installation to repair the installation to match the present hardware configuration.

Stop 0×0000007A = Run CHKDSK or other disk-repair diagnostic or replacing the hard drive or controller may resolve this problem.

Stop 0×0000007B = Installing incorrect device drivers when installing or upgrading storage adapter hardware typically causes stop 0×7B errors. Stop 0×7B errors could also indicate possible virus infection.

Run a virus protection scan to locate and remove any possible virus infections. Run CHKDSK or other disk-repair diagnostic or replacing the hard drive may resolve this problem.

Stop 0×0000007F = This could be caused by software problems or hardware failures. Removing and reinstalling updated drivers, software, or hardware may solve this problem.

Stop 0×0000009F = The Stop 0×9F message indicates that a driver is in an inconsistent or invalid power state. Restarting the PC may resolve this problem.

Stop 0xBE = Removing and reinstalling updated drivers may solve this problem.

Stop 0xC2 = This message is typically due to a faulty driver or software. Removing and reinstalling updated drivers may solve this problem.

Stop 0×000000CE = This message indicates that a driver failed to cancel pending operations before exiting. Restarting the PC may resolve this problem.

Stop 0×000000D1 = Drivers that have used improper addresses typically cause this error. Removing and reinstalling updated drivers may solve this problem.

Stop 0×000000D8 = Drivers that have used improper addresses typically cause this error. Removing and reinstalling updated drivers may solve this problem.

Stop 0×000000EA = Removing and reinstalling updated drivers, software, or hardware may solve this problem.

Stop 0×000000ED = This error might also occur during an upgrade to Windows XP Professional on systems that use higher throughput ATA disks or controllers with incorrect cabling. In some cases, your system might appear to work normally after you restart. Installing an 80-wire IDE cable may solve this problem.

Stop 0×000000F2 = Edge-level and level-interrupt-triggered devices are incorrectly assigned the same IRQ (for example, a serial port and a peripheral component interconnect (PCI) SCSI controller). Resetting Plug and Play/ESCD values in BIOS may solve this problem.

Stop 0xC000021A = Windows security system is unable to function. Running Windows setup to reinstall/repair may solve this problem.

Stop 0xC0000221 = Indicates driver, system file, or disk corruption problems (such as a damaged paging file). Faulty memory hardware can also cause this Stop message to appear. Replacing memory or resetting the pagefile may solve this problem.